• UK
  • US
  • Français
  • Deutsch
  • Español (precios €)
  • Polski
  • 日本人
  • 简化中国

signal8.head


signal8.p1

layout.datehead layout.vhead layout.sumhead
10/2024 8.03 layout.new
  1. Added support for the YINGCHI M series TMS stimulator.
layout.fixes
  1. Signal no longer crashes when importing into a file that is already open.
  2. DuoMag can once again deliver two pulses in independent triggers mode.
  3. In script defined dialogs, slider controls in integer mode had two problems: if a slider started at a value other than 0 it was incorrect and if you had a change function it would move after calling it. This also caused a tick to be missed.
  4. No longer crashes Signal if you try to sample with a configuration with pulse repeats not defined.
  5. Errors in the initial level for outputs are now reported correctly.
  6. Reject button now works between sweeps.
  7. The Magventure support now has more protection against spontaneous disarm if not fired for 5 minutes.
  8. The D360R conditioner dialog can no longer get stuck showing the wrong port after switching channels used for sampling.
  9. The Magstim Rapid could sometimes go into an error state when being used as an auxiliary states device. This was due to being sent commands too frequently.
  10. The Draw mode dialog for virtual channels now correctly initialises the check box to draw full width.
  11. Virtual channel wizard dialogs now cope better with changes to the preferred time units.
  12. Changes made to the state label online are now reflected in the State bar immediately.
  13. Using the Analogue trigger mode for peri-triggered sampling would cause sampling to hang if the waveform dropped below the lower threshold.
layout.changes
  1. RMT is now referred to as just MT as the motor threshold can used in either resting or active scenarios.
  2. Increasing the number of states no longer copies the state label to the new states.
  3. Active cursor dialogs now accept longer expressions.
  4. The x-axis dialog no longer tries to quote units if there are none.
  5. State labels are now used in state lists for auxiliary devices.
03/2024 8.02 layout.new
  1. Added Meas() function to the virtual channel system.
  2. Multiple frames uses Save changes dialog with stop button.
  3. Auxiliary states device settings are now saved in experimenter's notebook.
  4. Frame tagging, show buffer, frame overdrawing and changing the current frame can now be undone.
  5. Deleting cursors (vertical and horizontal) can now be undone.
  6. Info windows can now display state labels.
  7. Signal now attempts to prevent a user logging off or shutting down while sampling is in progress.
  8. Conditioner controls can now be accessed while sampling for multiple conditioners.
  9. It is now possible to drag attachments from an email in Outlook directly onto Signal, to have it open them. The files are copied to a folder in Downloads called Outlook (or Outlook(n) if a folder already exists there of that name).
  10. It is now possible to specify lists of states where a frame list would previously only allow one state.
  11. A new type of pulse item for additional actions has been added to the pulses dialog. Currently this only supports turning dynamic clamping models on or off.
  12. Pulse dialog now indicates the X zero position in the sampled data with a z below the control track.
  13. SampleStatus() has been enhanced to allow more detailed information about the status to be obtained.
  14. An error message is now given if a talker fails to run.
  15. Talker channels can now be duplicated in the sampling configuration.
  16. A warning is now given if you attempt to set up more than one conditioner on a given port.
  17. Adding channels from multiple talkers is now possible.
layout.fixes
  1. Dragging a pulse when using very fine timing resolution could fail to draw the new pulse location correctly during the drag.
  2. Can now change input for 1902 and have updated gain list online.
  3. Talker data could be missing after restarting sampling.
  4. PulseWaveSet() will truncate the number of waveform points if it would exceed the available 1401 memory when being used online.
  5. Arbitrary waveform points and DACs cannot be changed online.
  6. SampleStatus() could return incorrect information when used in a triggered script.
  7. Drift compensation strings have been corrected for talkers.
  8. Talker channels are now always listed correctly.
  9. Some USB/RS232 adaptors would fail to enter themselves into the registry and thus be excluded from the com port lists. Signal now checks for this and includes them with a basic COMn name.
  10. You can no longer drop files onto Signal when the File menu is unavailable.
  11. Triggered scripts were being run too early.
  12. Restarting sampling could, on some computers using a long USB cable, sometimes cause the 1401 device driver to unload and Signal to stop working.
  13. Closing the D360R control dialog while sampling could crash Signal.
  14. If a conditioner control dialog failed to open for any reason while sampling, the menu options to open any conditioner would be greyed out for the remainder of the sample run.
  15. It would sometimes take two attempts to close a conditioner control dialog while sampling.
  16. You can now import Intan rhd files that contain temperature sensor data.
  17. Protection has been added to prevent arbitrary waveforms being defined that would use more than the available space in the 1401 to store them.
  18. The 1902 setup dialog now initialises correctly when there is no configuration file.
  19. When using the D360R with a port offset applied, changes made by Digitimer software are reflected in Signal dialog.
  20. The SampleStop() script command now returns correct error codes if it fails for any reason.
  21. Tooltips now work again in script views.
  22. Previously, the automatic MEP detection mechanism available as part of the MTAT threshold measurement system would usually give incorrect results due to it analysing the wrong channel. This has now been fixed.
layout.changes
  1. When using the D360R conditioner setup with no configuration file, the dialog is populated with the current settings of the conditioner rather than default settings being used to change the conditioner.
06/2023 8.01 layout.new
    signal8.801new
layout.fixes
    signal8.801fix
layout.changes
    signal8.801change
10/2022 8.00 layout.new
    signal8.800new
layout.changes
    signal8.800change
Cambridge Electronic Design Limited

layout.reginengland: 00972132

layout.regoffice:

  • Cambridge Electronic Design Limited,
  • Technical Centre,
  • 139 Cambridge Road,
  • Milton,
  • Cambridge CB24 6AZ
  • ENGLAND.

VAT: GB 214 2617 96

layout.prodregno: WEE/BD0050TZ

layout.terms

layout.forourus.

DUNS: 219151016
CAGE/NCAGE: KB797
NAICS: 423490
layout.commoditycodes
Hardware: 84716070
Software: 85235190
×

support.email

info@ced.co.uk

support.post
  • Cambridge Electronic Design Limited,
  • Technical Centre,
  • 139 Cambridge Road,
  • Milton,
  • Cambridge CB24 6AZ
  • ENGLAND.
support.tel

(Int.+44) (0)1223 420186

support.tollfree

1 800 345 7794

×