• UK
  • US
  • Français
  • Deutsch
  • Español (precios €)
  • Portugal
  • Polski
  • 日本人
  • 中國傳統
  • 简化中国

CED 3505B Programmable attenuator with differential I/O


Overview

The 3505B incorporates differential I/O circuitry designed to maximise the signal-to-noise ratio at the attenuator output. This is particularly useful when using higher attenuation settings, giving an improvement in signal-to-noise ratio at the output of around 30dB compared with the front-panel BNC output. The differential I/O signals are available on a 6-pin ODU socket mounted on the 3505B front panel in place of the pulse out BNC or the headphone jack.

The 3505B price includes a 1m dual ODU plug cable that has BNC input and output connectors for interface to standard single-ended equipment. Also included is an un-wired ODU plug for the user to wire as required.

In addition, we offer a selection of I/O cabling for sale for use with both differential and single-ended user signals. The list includes a break-out box fitted with 3.5mm jack sockets that connect with standard 3.5mm TRS or TS leads. Cables are also available for daisy-chaining of 3505B attenuators using differential signalling. Connecting two or more attenuators in series that have a higher and a lower attenuation step size is a way of allowing fine resolution of attenuation changes in a large overall range of attenuations.

 

Signal routing

With the 3505B option, the attenuator output is permanently available both in single-ended form on the standard front panel BNC output connector and as a differential pair on the ODU connector.

The 3505B attenuator input is dynamically selectable to be taken from either the standard front-panel BNC input or the ODU input socket, the selection being determined by wiring on a selector pin on the ODU connector. If the pin is open circuit, the front-panel BNC input is used; if the pin is grounded, the ODU input is used. In this way, an ODU plug can be wired to work with either or both of input and output cables, or with an external switch closure to select the input to use. The break-out box mentioned in the overview above automatically switches whenever an input cable is plugged into the box.

I/O signal levels

To achieve maximal signal-to-noise ratio and to minimise the effect of external interference, balanced differential signals are twice the amplitude (as measured between signal+ and signal-) of an equivalent single-ended signal.

The design of the differential I/O circuitry on the 3505B is such that the -ve signal can be grounded on either or both of the input and output differential pairs so that the attenuator can be used with cabled single-ended connectors such as BNC plugs.

At the differential input, grounding the -ve pin of the input pair gives the expected simple divide-by-two on the +ve input signal, since the antiphase signal is zero.

At the differential output, the circuit is arranged so that, if the -ve output is grounded, the +ve output carries the whole differential signal at an amplitude that is twice that of the single-ended front-panel BNC output. Because of the matching ratios of two at the ODU input and output, use of BNC cabling from the ODU connector for both input and output gives 0dB gain or loss. However, using the BNC front-panel input in conjunction with ODU-cabled BNC output would give a 6dB increase in the output signal level. This should be borne in mind when planning laboratory configurations.

Daisy-chain cable showing series-connection of 3505B attenuators

The break-out box provides TRS sockets

Specifications

The differential option in the 3505B does not change the specification of the attenuator when it is used through the front-panel BNC inputs and outputs. When the differential inputs and outputs are used, the following characteristics apply (typical values given unless otherwise stated):

Input voltage maximum (differential) ±20V peak (+25dBu, 14V r.m.s.)
Input voltage maximum (single-ended) ±10V peak (+19dBu, 7V r.m.s.)
Input impedance (differential) 24 KOhm
Input impedance (common-mode) 18 KOhm
Input common-mode rejection 90 dB
Input offset voltage (differential) ±10 μV
Output voltage maximum (differential) ±20V peak (+25dBu, 14V r.m.s.)
Output voltage maximum (single-ended) ±10V peak (+19dBu, 7V r.m.s.)
Output impedance 50 Ohm
Output signal balance 54 dB
Output offset voltage (differential) ±10 μV
Output offset voltage (common-mode) ±50 mV
Output short-circuit current ±85 mA

5. Output signal-to-noise ratio (SNR) in dB 20Hz – 20KHz

Configuration A:fully differential I/O via ODU connector
Configuration B:single-ended BNC I/O via ODU connector
Configuration C:front-panel BNC input, ODU differential output
Configuration D:front-panel BNC I/O

Measurements taken on a 3505 attenuator with 3dB steps. SNR figures given are the ratio of in-band r.m.s. output voltages with input signal applied to the same with input grounded. The configuration C figures are corrected for the additional 6dB gain (see section 3 above).

Configuration A B C D
Attenuation dB SNR dB SNR dB SNR dB SNR dB
0 118 118 112 87
30 87 87 81 58
60 57 57 51 27

Cambridge Electronic Design Limited

Registriert in England: 00972132

Sitz der Gesellschaft:

  • Cambridge Electronic Design Limited,
  • Technical Centre,
  • 139 Cambridge Road,
  • Milton,
  • Cambridge CB24 6AZ
  • ENGLAND.

VAT: GB 214 2617 96

Herstellerregistrierungsnummer: WEE/BD0050TZ

Verkaufsbedingungen

Für unsere US-Kunden können wir das Steuerformular W-8BEN bereitstellen, mit dem wir als britisches Unternehmen identifiziert werden.

DUNS: 219151016
CAGE/NCAGE: KB797
NAICS: 423490
Warencodes
Hardware: 84716070
Software: 85235190
×

per e-mail:

info@ced.co.uk

per Post:
  • Cambridge Electronic Design Limited,
  • Technical Centre,
  • 139 Cambridge Road,
  • Milton,
  • Cambridge CB24 6AZ
  • ENGLAND.
Telefonisch:

(Int.+44) (0)1223 420186

Aus Nordamerika:

1 800 345 7794

×